MILLI-Q pure water machine common problem solving method
Hello everyone, my name is MILLI-Q is an important member of the Millipore family. In the last issue, I introduced you how to maintain our pure water machine. I believe everyone knows it! In this issue, I will introduce you how to solve some practical problems.
How can I change the filter column?
First adjust my state to the state of "STANDBA", then remove the filter column, then open my water intake switch, depressurize the system, and wait until I no longer flow out the water, then turn off the water intake switch. Remember, be sure to wait until I don't have water and then turn off the water intake switch, otherwise the system will not completely relieve the pressure.
Then I have a blue small door on the front, gently pull the lock piece on the left (one piece up and down), open the blue door, take out my "QUANTUM" column, and then put my white "QGARD" on the right side. The lid on the column is opened and the metal locking tab is removed so that the "QGARD" column can be removed.
Put the new "QGARD" column on me. At this time, I have to pay attention to a metal rod on the body to be aligned with the hole on the column. After pushing it to the left, lock the metal lock piece in the metal groove of the metal rod. Put the top cover on; put the new "QUANTUM" column into my blue door, push it in with a little force, then close the blue door, and when I hear the sound of my two locks, As for the explanation, my column is already in place.
Screw the pipe joint in the attachment into the water intake handle, and the street hose is led into the water tank; then open the water intake switch, I will enter the air exhaust program for 5 minutes. After 5 minutes, I will automatically enter the " In the state of OPERATE. Am I very smart?
Remove my pipe joints and hoses and install the terminal filter. At this time, be careful not to tighten the air cap on the filter, then open the water intake switch and wait until the water flows out of the air before tightening the air cap. Otherwise, the air does not hurry.
After the column is replaced, let me stay in the "OPERATE" state for 12 hours, so that I can work normally again.
How do you judge whether my pillar has reached the end of its life?
When I have been working for a while, first check how much time it takes for the resistance on my display to rise from the initial value to 18.2MΩ.cm when the water switch is turned to the cycle position. Under normal circumstances, it will not exceed 1 minute. of. In the case of a decrease in electrical resistivity (unstable) during the production process, it is proved that the life of my column has expired soon.
If I have a significant drop in water production (normally 1-1.5L per minute), most of the reason is that the terminal filter is blocked because I have no air in my body.
In order to ensure that I can work normally, and the most economical use of filter materials (filter columns, etc.), it is recommended that when the consumables are replaced, they can be replaced together.
About me (MILLI-Q) tips
Many older brothers and sisters may be negligent in their work. They will forget to add water to my bucket and let the air slip into my body. At this time, my display will show “AIR PURGEâ€, then I only need to open me. The water intake switch (open to the water production position), the display will show (AIR PURGE 5MN), after waiting for 5 minutes, my display will show "CLOSE THE VALVE", then turn off my water intake switch, I will again It works fine.
When I was working, was there occasionally a situation where the water pipes were not fixed and exposed to the water? This will not only let the air run into my body, but will even cause damage to my pump motor! Now you don't have to worry about it, Millipore has equipped the water tank for this problem, so that you can use it thoroughly!
Ok, my friends, do you understand our pure water machine family now? Or do you have any questions? You can call our technical hotline 0512-67283519 to ask.
Precise control
The vertical control accuracy is increased by 20%
The trajectory is more precise and the flight is smoother
Strong shock resistance
Responding to various complex vibration effects
The aging of the frame can also fly stable
Reduce the investment in after-sales maintenance
Multiple redundant backup
Triple redundancy imu
Dual redundant barometers
Flying is safer
Noise reduction and power saving
The motor noise is three times smaller
Save 5~15% electricity
The flying sound is even smaller
Flight Control,Flight Sim Controls,Flight Simulator Controls,Flight Simulator Joystick
Dongying Youjia Industry & Trade Co. Ltd. , https://www.uav55.com