Breeding and breeding of budgies
After selecting a pair of budgerigars that you like. We should spend some time on food, nest boxes, and cages.
First, food
As we all know, the main food for budgies is generally fed millet. Regarding whether it is shelled or shelled, I personally prefer shelling. Shelled millet may cause some nutrient loss. However, these nutrients I think can be completely replaced from other channels. Moreover, the shelled millet is convenient for both the owner and the tiger skin, saving time and labor, and it is entirely outweighed by the disadvantages!
For tiger skins to be bred, I just think that it is not enough to feed Xiaomi. This will make the veteran may not be able to bear the hardships of brooding, shortened its life span, and even bizarre premature death. For chicks, it may also cause them to develop slowly/poorly and have a low survival rate.
I suggest that in addition to millet, we should also increase:
1. One cuttlefish bone, lifted with wire. It can either make the bird feed on calcium supplements or it can serve as a toy for the male during the incubation period. Male male birds have plenty of energy and are very active. When a female bird hatches, he is likely to enter and leave the hatchery box frequently during the hatching period and when the young bird is hatched. This will inadvertently trample eggs and young chicks, resulting in adverse consequences. It is important that the male bird has something to do.
2. Green leafy vegetables and fruits (green vegetables, apples) to supplement moisture and vitamins. It can also improve the vomiting of the parent bird. Note: Be careful about pesticides. My vegetables are usually planted all year round (don't believe it, I'll use the moon cake box in the balcony).
3. The rice we eat. In the beginning, tiger skins generally did not like to eat rice. But my tiger skin will eat rice. Give time, let the bird adapt slowly, you will find that tiger skin can eat a lot of things! Rice is used to supplement tiger skin (especially small birds) with carbohydrates and certain plant fats. The tiger skin from snack rice is obviously larger, has better physical strength, and develops faster.
4. Sand or broken bricks (note to sterilize). Another bottle hangs to supplement the bird's mineral intake.
Second, Xiaomi’s knowledge
Feeding the budgie's egg millet is different:
1) Mix the egg with dried rice. In raw egg whites, I discovered that there are substances that make the skin of the tiger skin estrus. Eating tiger eggs with raw eggs and millet is relatively easy to reproduce. Only during the aphrodisiac period.
2) Steamed millet dried eggs. Xiaomi chose this from the hatching of the bird.
3) Pu millet. Feed the newly emerged bird only to it to breed.
Third, the nest box
Budgie's nest box, individuals have personal opinions. The nest boxes (two-story, spired wooden house) that are generally sold on the Shanghai market are not favored by me except when they were first used. In one word: This nest box is so rotten.
Tiger's incubator, I usually do it myself. Later, I paid for the woodwork to save me some strength by following my own nest box.
The tiger's nest box (inner wall) I designed had three bird widths (about 10 to 15cm), one half bird body (about 20cm) long, and a height of one bird more (about 10 to 12cm).
Tiger's nest box, I usually use a layer. Pay attention to ventilation and ventilation, but try not to see light. Ventilation depends on the local climate (temperature, humidity) and season (if you wish to have a guaranteed breeding rate throughout the year).
The selection of the material for tiger skin boxes was also something I considered.
Bottom: to have a certain thickness (about three cm thick or more, but not too thick, so that the nest box is very heavy), wood I usually use pine, easy to get, natural fragrance, the basic durability of more than a year, and not too Increase the overall weight of the nest box.
Focus: An egg pit will be drilled on the floor of my nest box. So, you now understand why the nest box is three centimeters thick:) Give it a try.
The width of the board, generally slightly thicker, can be set on the nail, bearing, that is their task.
Before and after the door panel, the general composite board on it. Thin for easy hole.
On the top cover, the cover made of iron sheet. Uses: explain later.
All right, having a nest is all right? I'm sorry, I'm a little perfectionist. Listen again:
Nesting box as far as possible outside the cage, in order to observe and clean up. Sawdust should be laid in the nest box to keep the nest box clean and tidy. Each litter has a nest and the nest box should be disinfected and cleaned. It is recommended that clear disinfection of the nest box with boiling brine (or appropriate amount of potassium permanganate water), then wash with water, set the sun exposure and disinfection. The exposure method also applies to the treatment of sawdust.
Water treatment agents refer to chemicals used for water treatment. Usually referred to as chemicals used for sewage treatment. Widely used in chemical, petroleum, light industry, Daily Chemical, textile, printing and dyeing, construction, metallurgy, machinery, medicine and health, transportation, urban and rural environmental protection and other industries, the main purpose is to remove suspended solids and toxic substances in water, control the formation of scale, sludge, reduce the corrosion of water contact materials, deodorization, sterilization, decolorization, soft To stabilize water quality and desalination, so as to save water and prevent water pollution. It includes chemicals needed for cooling water and boiler water treatment, seawater desalination, membrane separation, biological treatment, flocculation and ion exchange technology. Such as corrosion inhibitors, scale inhibitors and dispersants, bactericides and algae killers, flocculants, ion exchange resins, purifiers, cleaning agents, pre-film agents and so on. The main products of water treatment agents include organic phosphorus water treatment agents, polycarboxylic acid water treatment agents, composite scale and corrosion inhibitors, bactericides and algae killers and other water treatment agents.
Our Services
1. OEM(????) service is available.
2. Fast producing time.
3.Cheapest price forproduces.
4. Reply promptly in 24 hours.
5.Free sample available.
FAQ
Q1: product specifications?
A: we will pack the product specifications according to your needs.
Q2: Do you have some videos where we can see the line production?
A: Yes, we can provide some videos for reference. (yes, we can provide some videos).
Q3: How about payment terms? What kind of payment terms do you have?
A: 30% TT deposit + 70% TT before shipment, 50% TT deposit + 50% LC bala
Nce, Flexible payment can be negotiated.
Q4: what advantages do you have?
A: the quality of the products we offer can be guaranteed and will provide you with very competitive prices.
If you have any questions, please contact with us directly. Organic Intermediate are produced by HRT bearing With High Quality and Good Appearance. Welcome you can visit our Factory. For inqury, please send mail directly to us.
Water Treatment Agent,Trans-Benzylideneacetone 99%,Sodium Allysulfonate,Water Treatment Chemical Agent
Shandong Chenyi Environmental Protection Technology Co.,Ltd , https://www.chenyichemistry.com