Emergency repair of common eight faults in agricultural vehicles
Air cushion burnout: When the burned area is small, use an asbestos line to fill in. When the burned area is large, use the same part of the waste cylinder pad of the same thickness to cut off a piece of shimmy, knock it carefully, and make it fit well; if burned out Between the two cylinders, the asbestos line must be wrapped in copper.
Radiator leakage: If there is any breakage in the water inlet and outlet hoses, use a piece of cloth to coat the leaky place with soap, and then tie the wire tightly. If the breakage is serious, cut it into two pieces with a knife from the broken part of the hose. Use suitable bamboo. Tubes and so on in sets between the hose, and then tightly tied with wire, and then can be installed; radiator core copper pipe with a slight leak, the use of soap can be stuck at the leak. If the leak is serious, use pliers to clamp the leak so that it does not leak.
Valve spring breaking: If only one point is broken, two breaking springs can be installed and used. If several springs are broken, multiple cylinders can remove the adjusting bolts of the inlet and exhaust valves of the cylinder and close the valve to make the cylinder. Stop working and cut off oil.
Sudden loss of power in the middle: When the horn does not ring suddenly, no light is turned on, and the starter does not turn, it means that the vehicle is completely powered off. At this time, you can first check whether the pile head of the battery is loose. Do not squawk when inspecting. You can use a pair of pliers to test the two pile heads. If there is no spark, then the pile head is loose, tighten with a wrench. If the pile head is tight and clean, the power failure phenomenon is still not eliminated. , Can check the two-stage wire connection, such as poor contact, timely repair; If the battery has a single cell damage, can be used directly to connect a good single cell grid.
Clutch tightening: If the friction plate is stained with oil, you can step on the clutch pedal, use the oil gun to install gasoline, and then use the oil on the flywheel to dissolve it temporarily. (If no oil gun and substitute, you can use plastic pipe or rubber hose to suck oil. Align the shot); If the friction piece slips due to burning, it will be able to burn the damaged part, but when starting to drive, it should be stable and the speed change action should be rapid.
The leaf spring breaks: According to the situation, the steel plate spring, the wooden block between the axle and the frame, and the iron wire are used for temporary use to replace the repair point.
Jack-less change of tires: replace the double-row tires, the inner wheel can be lifted with wooden blocks or bricks, so that the outer wheel can be vacant, you can replace; replace the front wheel or single tire, available wood or brick, stone The front axle or rear axle pad is stable, digging underneath the tire to be dismantled to make the tire fly, it can be replaced.
Damaged fan tape: Broken fan tape, mostly broken. Several ropes can be used for tightening the ropes. The length and thickness of the ropes should be similar to those of the original fan tape, but the ropes should be wound in the middle and cannot be exposed. Then they can be tightly tied with iron wires; Holes, temporarily connected with coarse wire. However, the law should test the engine for a few minutes to check if the fan rotation is normal.
Radiator leakage: If there is any breakage in the water inlet and outlet hoses, use a piece of cloth to coat the leaky place with soap, and then tie the wire tightly. If the breakage is serious, cut it into two pieces with a knife from the broken part of the hose. Use suitable bamboo. Tubes and so on in sets between the hose, and then tightly tied with wire, and then can be installed; radiator core copper pipe with a slight leak, the use of soap can be stuck at the leak. If the leak is serious, use pliers to clamp the leak so that it does not leak.
Valve spring breaking: If only one point is broken, two breaking springs can be installed and used. If several springs are broken, multiple cylinders can remove the adjusting bolts of the inlet and exhaust valves of the cylinder and close the valve to make the cylinder. Stop working and cut off oil.
Sudden loss of power in the middle: When the horn does not ring suddenly, no light is turned on, and the starter does not turn, it means that the vehicle is completely powered off. At this time, you can first check whether the pile head of the battery is loose. Do not squawk when inspecting. You can use a pair of pliers to test the two pile heads. If there is no spark, then the pile head is loose, tighten with a wrench. If the pile head is tight and clean, the power failure phenomenon is still not eliminated. , Can check the two-stage wire connection, such as poor contact, timely repair; If the battery has a single cell damage, can be used directly to connect a good single cell grid.
Clutch tightening: If the friction plate is stained with oil, you can step on the clutch pedal, use the oil gun to install gasoline, and then use the oil on the flywheel to dissolve it temporarily. (If no oil gun and substitute, you can use plastic pipe or rubber hose to suck oil. Align the shot); If the friction piece slips due to burning, it will be able to burn the damaged part, but when starting to drive, it should be stable and the speed change action should be rapid.
The leaf spring breaks: According to the situation, the steel plate spring, the wooden block between the axle and the frame, and the iron wire are used for temporary use to replace the repair point.
Jack-less change of tires: replace the double-row tires, the inner wheel can be lifted with wooden blocks or bricks, so that the outer wheel can be vacant, you can replace; replace the front wheel or single tire, available wood or brick, stone The front axle or rear axle pad is stable, digging underneath the tire to be dismantled to make the tire fly, it can be replaced.
Damaged fan tape: Broken fan tape, mostly broken. Several ropes can be used for tightening the ropes. The length and thickness of the ropes should be similar to those of the original fan tape, but the ropes should be wound in the middle and cannot be exposed. Then they can be tightly tied with iron wires; Holes, temporarily connected with coarse wire. However, the law should test the engine for a few minutes to check if the fan rotation is normal.
Hot Sale SARS-CoV2(COVID-19) Test Kit
NINGBO AUTRENDS INTERNATIONAL TRADE CO., LTD , https://www.metests.com