Use and troubleshooting of wheat planter
Wheat sowing has the characteristics of uniform seeding, consistent depth, stable row spacing, good earth covering, saving seeds, and high work efficiency.
Correct use of seeder should master the following points:
(1) After the seeder is attached to the tractor, it must not be tilted. When working, it should be horizontal before and after the rack.
(2) Before the formal sowing, first 10-20 meters of the pilot planting in the land, observing the working conditions of the planter, and formal sowing after reaching the agronomic requirements.
(3) Firstly, the land should be broadcasted horizontally so as not to harden the land and cause the broadcast depth to be too shallow.
(4) Observe the working conditions of the seed metering device, opener, cover, and transmission mechanism during sowing, such as clogging, clay, tangled grass, loose seed coverage, and remove it in time.
(5) When the planter is working, it is forbidden to reverse or turn sharply. The planter's lifting or landing should be performed slowly to avoid damage to the machine.
(6) The seed in the seed box must not be less than 1/5 of the seed box capacity during the operation; when transporting or transferring the land, the seed box must not contain seeds, and no other heavy objects can be pressed.
(7) The work of adjusting, repairing, lubricating, or cleaning up the grass must be carried out after parking.
Faults are eliminated in time.
(1) Seedlings are not seeded. The main reason is that the transmission gear is not meshed, or the square hole of the row head gear is worn out, adjusted, repaired or replaced.
(2) Individual metering devices do not work. The reason is that the individual seeding boxes in seed shelving or metering device mouth are blocked by debris, should be replaced with cleaning and seeds; row pin and individual seedling grooved wheel connection pin broken, should replace the pin; individual seed box The card is not pulled open and the card should be pulled open.
(3) Seedlings are planted, but there are no seeds in individual species. The reason is that the opener or seed tube is blocked (mostly occurs on the opener on the ground wheel), and the plug should be cleaned and appropriate measures taken to prevent debris from falling into the opener.
(4) The seeds are kept out of control and lose control. The reason is that the release pin of the clutch stay is missing or the separation gap is too small, and the pin should be reattached and locked, or the separation gap should be adjusted.
(5) The seeding is intermittent and the seeding is uneven. The reason is that the meshing clearance of the transmission gear is too large and the gears should slip. Adjustment should be made; the spring force of the clutch spring is too weak and the gears should be slippery. The spring should be adjusted or replaced.
Correct use of seeder should master the following points:
(1) After the seeder is attached to the tractor, it must not be tilted. When working, it should be horizontal before and after the rack.
(2) Before the formal sowing, first 10-20 meters of the pilot planting in the land, observing the working conditions of the planter, and formal sowing after reaching the agronomic requirements.
(3) Firstly, the land should be broadcasted horizontally so as not to harden the land and cause the broadcast depth to be too shallow.
(4) Observe the working conditions of the seed metering device, opener, cover, and transmission mechanism during sowing, such as clogging, clay, tangled grass, loose seed coverage, and remove it in time.
(5) When the planter is working, it is forbidden to reverse or turn sharply. The planter's lifting or landing should be performed slowly to avoid damage to the machine.
(6) The seed in the seed box must not be less than 1/5 of the seed box capacity during the operation; when transporting or transferring the land, the seed box must not contain seeds, and no other heavy objects can be pressed.
(7) The work of adjusting, repairing, lubricating, or cleaning up the grass must be carried out after parking.
Faults are eliminated in time.
(1) Seedlings are not seeded. The main reason is that the transmission gear is not meshed, or the square hole of the row head gear is worn out, adjusted, repaired or replaced.
(2) Individual metering devices do not work. The reason is that the individual seeding boxes in seed shelving or metering device mouth are blocked by debris, should be replaced with cleaning and seeds; row pin and individual seedling grooved wheel connection pin broken, should replace the pin; individual seed box The card is not pulled open and the card should be pulled open.
(3) Seedlings are planted, but there are no seeds in individual species. The reason is that the opener or seed tube is blocked (mostly occurs on the opener on the ground wheel), and the plug should be cleaned and appropriate measures taken to prevent debris from falling into the opener.
(4) The seeds are kept out of control and lose control. The reason is that the release pin of the clutch stay is missing or the separation gap is too small, and the pin should be reattached and locked, or the separation gap should be adjusted.
(5) The seeding is intermittent and the seeding is uneven. The reason is that the meshing clearance of the transmission gear is too large and the gears should slip. Adjustment should be made; the spring force of the clutch spring is too weak and the gears should be slippery. The spring should be adjusted or replaced.
Burdock Root,Burdock Plant,Burdock Oil,Organic Burdock Root
Yirun Agricultural Cooperative , https://www.yiruncn.com