Feeder maintenance and cleaning
The feeder is used as a machine for conveying materials. The application industry is very extensive and is one of the necessary equipment in light industry and heavy industry.
The principle is also the machine that carries out the required transportation of the material by means of the motion generated by the electric power and the force of the motion is applied to the material. In modern power feeders, the technology has revolutionized the power. For example, some emerging technologies such as high-pressure air and ultrasonic power transmission have begun to be used in feeders. Shenzhen Quntai Machinery Equipment Co., Ltd. as the feeder industry in Shenzhen, the earliest professional manufacturer of stamping peripheral automation equipment, through years of accumulation, in the use and maintenance of feeder equipment, there are Shenzhen research, the following twelve steps are summarized:
In the first step, before the machine is started, it is necessary to check whether the whole machine is in a normal state.
In the second step, when the equipment is running, no one is allowed to do other work on the machine.
The third step must be connected to the oil pipe and power supply before starting the machine. The feeder hydraulic system must be turned on before the production commissioning to bring the pressure to the set pressure.
The fourth step, the feeder operator must be familiar with the operating rules of the machine, and all the unrelated personnel should not operate.
The fifth step, the mechanical components, circuits and operating procedures of the feeder shall not be arbitrarily modified without professional technicians, otherwise it may cause undesirable phenomena.
The sixth step, the feeder fails during use, must press the emergency stop button, and cut off the main power switch, no mistakes, and quickly check the cause. Do not power on until the fault is removed.
The seventh step, when there is a sudden power outage and an abnormal accident, it is necessary to remove the residual material in the barrel in time.
The eighth step, during the use of the feeder, must be maintained frequently, and regular inspection of electrical components, line terminals, etc., to eliminate hidden dangers.
The ninth step, maintenance machine requirements: generally cleaned once every three months. (Users are advised to clean up every two months)
The tenth step is to strictly control the appropriate oil supply. If the oil supply is too small, the pressure, lubrication and cooling effects are not good, causing the machine to overheat and increase the mechanical wear. It should be minimized while maintaining pressure, lubrication and cooling. Excessive oil supply will cause excessive pressure, which will seriously affect product quality and waste lubricant.
In the eleventh step, before refueling or refueling the old machine, the lubricating oil pipeline and fuel tank must be cleaned, and no oil or impurities, especially iron filings, must be left. When refueling, put it into the fuel tank according to the specified amount of oil and recycle it.
In the twelfth step, the safety guard on the equipment is not allowed to move freely, and it is not allowed to modify or deliberately make it useless.
Through the above twelve steps, not only can the accident caused by misoperation be reduced, but also the common maintenance method of the feeder can extend the life of the machine.
The principle is also the machine that carries out the required transportation of the material by means of the motion generated by the electric power and the force of the motion is applied to the material. In modern power feeders, the technology has revolutionized the power. For example, some emerging technologies such as high-pressure air and ultrasonic power transmission have begun to be used in feeders. Shenzhen Quntai Machinery Equipment Co., Ltd. as the feeder industry in Shenzhen, the earliest professional manufacturer of stamping peripheral automation equipment, through years of accumulation, in the use and maintenance of feeder equipment, there are Shenzhen research, the following twelve steps are summarized:
In the first step, before the machine is started, it is necessary to check whether the whole machine is in a normal state.
In the second step, when the equipment is running, no one is allowed to do other work on the machine.
The third step must be connected to the oil pipe and power supply before starting the machine. The feeder hydraulic system must be turned on before the production commissioning to bring the pressure to the set pressure.
The fourth step, the feeder operator must be familiar with the operating rules of the machine, and all the unrelated personnel should not operate.
The fifth step, the mechanical components, circuits and operating procedures of the feeder shall not be arbitrarily modified without professional technicians, otherwise it may cause undesirable phenomena.
The sixth step, the feeder fails during use, must press the emergency stop button, and cut off the main power switch, no mistakes, and quickly check the cause. Do not power on until the fault is removed.
The seventh step, when there is a sudden power outage and an abnormal accident, it is necessary to remove the residual material in the barrel in time.
The eighth step, during the use of the feeder, must be maintained frequently, and regular inspection of electrical components, line terminals, etc., to eliminate hidden dangers.
The ninth step, maintenance machine requirements: generally cleaned once every three months. (Users are advised to clean up every two months)
The tenth step is to strictly control the appropriate oil supply. If the oil supply is too small, the pressure, lubrication and cooling effects are not good, causing the machine to overheat and increase the mechanical wear. It should be minimized while maintaining pressure, lubrication and cooling. Excessive oil supply will cause excessive pressure, which will seriously affect product quality and waste lubricant.
In the eleventh step, before refueling or refueling the old machine, the lubricating oil pipeline and fuel tank must be cleaned, and no oil or impurities, especially iron filings, must be left. When refueling, put it into the fuel tank according to the specified amount of oil and recycle it.
In the twelfth step, the safety guard on the equipment is not allowed to move freely, and it is not allowed to modify or deliberately make it useless.
Through the above twelve steps, not only can the accident caused by misoperation be reduced, but also the common maintenance method of the feeder can extend the life of the machine.