Capsule machine|Capsule filling machine|How to use capsule filling machine
How to use the capsule machine:
This manual uses the HLT-400 split sleeve machine as an example. The HLT-187 and HLT-187 joint sleeve machines can be used for reference.
1. The aluminum alloy has a guide port for the B machine, the aluminum alloy has no guide port for the A machine, and the small body is the lock machine.
2 , AB machine, as long as the three plugs are connected to the power supply, press the green switch of the distribution box. However, the knob of the regulator knob must be aligned to zero when pressing the green switch. If the tip of the pair is above 100 , the green switch will be pressed, the regulator will not adapt, and the voltage regulation will be completed within 6 seconds.
3 , A template and B template, the middle plate belongs to the tape, and the mark is not assembled on the machine, please look for it.
4 , the aluminum alloy plate is called the arranging plate, the wrong plate below the arranging plate (also called the movable plate), and the two ends are equipped with springs, which can be pushed.
5, the movable plate template below two sideways care article, the B discharge machine B templates, the template A is A discharge machine, the position of the movable plate placed below, above, to care article. When all the capsules on the alignment plate are full, just push the template into it. At this time, all the 400 capsules on the alignment plate fall into the template (if it is not clean, you can push it back and forth. Once, the action is fast), then step on the footboard and remove the template. The A machine and the B machine use the same method.
6. When loading the powder, use a table with a table size. Spread the powder on the B plate and level off to remove excess powder. Due to the different powder properties, some powders with a light body weight can be used in our company's powder board.
7. Cover the A plate with the capsule A head with the intermediate plate. The middle plate must be two notched upwards, then pick up the A plate with the middle. Turn over and cover it on the B board. The plate holes are aligned with the hand-pushing gesture, and the 400 capsules have all entered the pre-lock state.
8. Press the green switch. At this time, the locker is still not working. When you push the template containing the powder from the bottom of the locker of the locker into the stroke switch, press the plate down, press it and remove it. The template, the locker has stopped automatically. At this point, the rubber pellets have all entered the lock, then the A plate is removed, and then the middle plate is picked up and placed on the same size plate as the template, and the plastic plate is poured into the box for temporarily placing the rubber pills. Inside (Before pushing the template into the locker plate, please stand the pre-locked rubber pellets on the front side of the locker and touch the two plexiglass strips to clean the remaining powder).
Maintenance and repair considerations
  1. The speed reducer in the locker is replaced by oil within 24 hours after the accumulated use, and the oil is replaced within 72 hours after the second use. Replace every few months in the future.
  2 , when changing the model, as long as the middle link is rotated, the height difference of the pressure plate is generated. From 0# to 1# , 2# is turned clockwise, so 2# is adjusted to 1# , 0# is Turn counterclockwise. Emphasis is placed here: ( 1 ) When rotating the connecting rod, the connecting rod and the crankshaft must be perpendicular, that is, when the upper pressing plate is raised to zoi, the connecting rod and the crankshaft are also perpendicular, and then the rotation can be performed. ( 2 ) The upper and lower screws of the connecting rod must be loosened before rotating. ( 3 ) Each rotation must be rotated on the basis of a 180 degree angle. For example, a 180- degree angle, two 180- degree angles, and three 180- degree angles, regardless of inversion or forward rotation, require a 180- degree angle. Otherwise the gear unit will be damaged when it is turned on.
  3. Replace the model of the alignment machine: ( 1 ) The slit of the rubber pellet is level with the surface of the alignment plate. The adjustment position is the height of the two ends of the board. The screws are in the long holes of the straight support plate. ( 2 ) Adjust the distance between the push-pull plate and the movable plate. The upper plate surface of the plywood is spaced 3 mm from the lower plate surface of the movable plate. Adjust the two-head screw and the long rod in the box. After the adjustment is correct, the screw should be tightened, and the foot lever should be close to the lower edge of the box.
  4. The alignment plate and the movable plate must be misaligned (the movable plate is also called the misaligned hole plate). When the pull-in plate is pushed into the bottom, the hole positions of the alignment plate movable plate and the three-piece plate should be aligned. If the hole positions are not aligned, adjust the misalignment position of the movable plate and the alignment plate.
Adjustment method: ( 1 ) Twist the screws of the straight support plate and the angle support, and the straight support plate can drive the horizontal plate and the movable plate to be misaligned. ( 2 ) Twist the upper and lower screws of the shrapnel so that the assembly frame drives the alignment plate into a misalignment.
  5. Troubleshooting: After the start switch of the machine is arranged, the regulator can work normally and the assembly frame does not vibrate: ( 1 ) the head and the block screw are loose; ( 2 ) the alignment plate and the assembly frame are loose; ( 3) ) The shrapnel and the shrapnel screws are loose; ( 4 ) Please check the tightness of each screw.
The regulator is sometimes heavy, and sometimes it is lightly displaced after the carbon brush breaks. The regulator should be replaced. Pay attention to the switch and then the regulator.
1. After the capsule is successfully assembled, the dust on the surface of the capsule can be removed. The polishing machine of our factory can be used.
2 , it is recommended to buy a split capsule.
If you want to know more about capsule machine, please log in to our company:< > Or directly:
Â
Product categories of Disposable Face Mask,
we are specialized manufacturers from China on Chinese PPE Export Whitelist,
Disposable Face Mask,
Disposable Face Mask suppliers/factory,
wholesale high-quality products of Disposable Face Mask R & D and manufacturing,
we have the perfect after-sales service and technical support. Look forward to your cooperation!
3Ply Disposable Mask,Medical 3Ply Disposable Mask,Nonwoven 3Ply Disposable Mask,Protective 3Ply Disposable Mask
CAREABLE BIOTECHNOLOGY CO,. LTD , https://www.careablemask.com